Design · How it works
No glue, no clips: the hidden tube and tiny number that hold LEGO® bricks together
A 1958 patent moved a hollow tube to exactly the right spot. Add plastic that gives a little and moulds the LEGO Group says are accurate to about 0.005 mm, and you get a grip that has lasted nearly seven decades.
Watch the film · 1:09
Press two LEGO® bricks together and they hold. Pull them apart and there is nothing to explain it: no glue, no clip, no latch, just plastic.
What does the work is a piece of geometry most people never look at, on the underside of the brick, plus a very small amount of give in the plastic. The LEGO Group calls the result clutch power. It is also why, in the company’s words, “bricks produced over 60 years ago fit with those made today.”
The story of how that fit came about involves a borrowed idea, a well-timed patent, and a plastic that did not always keep its shape.
By the numbers
- Tube patent application filed
- Jan. 28, 1958
- U.S. patent granted
- 1961
- Stud spacing (nominal)
- 8.0 mm
- Stud diameter (nominal)
- 4.8 mm
- Mould accuracy, per the LEGO Group (2022)
- 0.005 mm
- Typical scalp hair width
- 60 to 80 µm
- ABS used from
- 1963
- Ways to combine six 2×4 bricks
- 915,103,765
Mould accuracy is the LEGO Group’s own figure; over the years it has published values from 0.004 to 0.01 mm. Brick dimensions are widely used nominal values, not an official LEGO® specification.
Hollow bricks, then tubes
The LEGO Group did not invent the plastic building brick, and its own history says so. Its account of its early Automatic Binding Bricks credits the toymaker Hilary Fisher Page and his company Kiddicraft, which “has invented the plastic bricks.”
The early LEGO® bricks had studs on top but were open underneath. “All bricks up until this point are hollow, reducing the stability of constructed models,” the company’s history notes, adding that the hollow design drew complaints. Stack them, and they did not hold together well.
The fix came in 1958. On January 28 of that year, at 1:58 in the afternoon, according to the company, the LEGO Group submitted a patent application for a new kind of toy building element. The inventor named on the United States version, granted in 1961, is Godtfred Kirk Christiansen. The new element added something underneath the brick: hollow tubes.
Between four studs, not under one
The clever part is where the tubes go. Earlier hollow blocks, the patent explains, placed internal projections directly in line with the studs on top. Christiansen’s design moved them. In the patent’s words, the tubes are “arranged co-axially with the centre of a square defined by four primary projections.” Each tube stands in the gap between four studs, and the patent specifies that it touches all four.
The numbers are tidy. On a standard brick, studs sit 8 millimeters apart and are 4.8 millimeters across, according to widely used nominal measurements. Work out the diagonal of that square of studs, subtract one stud, and you get a tube about 6.5 millimeters wide, just big enough to touch all four.
Now press one brick onto another. Each stud from the brick below slides into the space between a tube and the outer wall of the brick above. The LEGO Group’s own help page puts it simply: “The studs get neatly wedged in between the tubes and the sides of every brick making them stick together firmly.”
The wedge works because the stud is a little too big for its slot. Brick Architect, a guide to LEGO® parts, describes the connection as an “interference fit,” because “a stud is slightly larger than the opening in the underside” of a brick. When the parts are pressed together, the plastic gives slightly and pushes back. Brickfact reports that measured studs come out about a tenth of a millimeter larger than the 4.8 millimeter design value, and describes that slight flex as what the company calls clutch power. “Combined, the studs and tubes create clutch power,” as the LEGO Group puts it.
The film · 1:09
Clutch Power
A clay-animated look under a LEGO® brick, where each stud is squeezed between a tube and a wall, and why a 1958 brick that kept its shape still clicks.
Watch more on Instagram Follow CERAMICO
Read the transcript
No glue. No clips. So what holds two LEGO bricks together? Why does a 1958 brick still grip today's? A hidden tube. One tiny number. Early LEGO bricks were hollow underneath. Models wobbled. So in 1958, LEGO filed a patent: tubes inside. But tubes don't sit under studs. Each stands between four. Press down: each stud wedges between tube and wall. The stud's slightly too wide, so the plastic gives, and grips. That squeeze is clutch power. But every stud must match. LEGO says its moulds work to about 0.005 mm. Roughly a tenth of a hair. The catch: the first bricks' plastic can warp. So from 1963, LEGO switched to steadier plastic: ABS. The plastic changed, the fit didn't. A 1958 brick that kept its shape still clicks. Send this to whoever kept their parents' bricks. Just a stud, a tube, a squeeze. That's why there's...
Animated model, illustrative and not to scale.
Roughly a tenth of a hair
A grip like this depends on every stud and every tube being almost exactly the same size. A stud that is too small would not grip, and one that is too large would not fit easily.
So the moulds have to be extremely precise, and the LEGO Group has said so for decades, though its numbers have varied. In 1963, its history says, moulding was done “to an accuracy of 1/200 mm,” or 0.005 millimeters. A 2010 company profile gave 0.01 millimeters. A 2018 release said 0.004 millimeters. A 2022 release returned to 0.005 millimeters, or 5 micrometers.
A stud that is too small would not grip, and one that is too large would not fit easily.
For scale, scalp hair is “a fiber 60 to 80 μm in diameter,” according to a 2003 dermatology review. Five micrometers is roughly a tenth of that, which matches the company’s own help page, which speaks of “1/10th of a hair’s width precision.”
Two caveats are worth keeping in mind. These are figures the LEGO Group publishes about its moulds, not independent measurements, and no outside measurement of its mould accuracy appears in public. They also describe the moulds, not a guarantee that every finished brick is within 0.005 millimeters.
The plastic changed, the fit didn’t
There is a catch in the promise that old bricks fit new ones. The first LEGO® bricks were not made of the plastic used today. Until 1963, the company’s history says, it used cellulose acetate, “which is based on wood.” That year it began switching to ABS, which it describes as “more stable and color fast.”
Collectors know what “more stable” means in practice. “CA has a tendency to warp over time, often severely,” BrickNerd wrote in 2026, adding that many of these bricks “are now incompatible with modern bricks due to this deformation.” Brickset says early bricks exposed to heat and humidity warped, which led to gaps and difficulty stacking. The change was not overnight, either: Brickset says cellulose acetate was not phased out completely until 1972, and BrickNerd puts the end at 1970, with Samsonite, in the United States, as the last holdout.
So the accurate version of the company’s compatibility claim comes with a condition. The geometry of studs and tubes has stayed the same. A 1958 brick that kept its shape will still click onto one made this year. One that warped may not.
ABS is still the brick material in 2026, though where it comes from is changing. In March 2026, the LEGO Group reported that renewable and recycled content rose to 52 percent of the materials it bought for bricks in 2025, largely through certified mass balance and segregated materials. BrickNerd reported that the company had abandoned its effort to make recycled PET work as an ABS replacement.
The coupling itself has outlasted its patent and its original plastic. And the possibilities it opens are not small: the company says six 2×4 bricks can be combined in 915,103,765 different ways, a figure a University of Copenhagen mathematician confirmed. All of them depend on a stud, a tube, and a squeeze.
Sources
Every line in the film was checked against these sources by an independent fact-checker before publication. Company claims are attributed to the company that made them.
- The LEGO Group: brand logo file
- Harvard BioNumbers: Diameter of human scalp hair (Wolfram, 2003)
- Brick Architect: Basic LEGO parts guide
- Brickfact: Lego brick dimensions, studs, plates and bricks in mm (2026)
- BrickNerd: Every type of plastic used by LEGO, 2026 edition
- Brickset: Significant events of the 1960s
- Victoria and Albert Museum: LEGO System construction toy
- Wikimedia Commons: LEGO logo
- Wikipedia: Hilary Page
- Wikipedia: Lego
- LDraw parts library: Brick 2 x 4 (3001)
- Google Patents: US 3,005,282, toy building brick (1961)
- The LEGO Group: Company profile 2010 (archived PDF)
- University of Copenhagen (Eilers): 915,103,765
- Bartneck: LEGO brick dimensions and measurements
- The Brothers Brick: LEGO celebrates 60 years (2018)
- The LEGO Group: LEGO bricks in the making
- The LEGO Group: Brick by brick, building LEGO love for 90 years (2022)
- The LEGO Group: Celebrating 60 years of LEGO bricks (2018)
- The LEGO Group: Record results in 2025 (2026)
- The LEGO Group: Automatic Binding Bricks
- The LEGO Group: Quality in every detail
- The LEGO Group: The stud and tube principle
- The LEGO Group: Fair Play trademark guidelines
- The LEGO Group: How do LEGO bricks work?
- LUGNET: LEGO dimensions FAQ
Updates and corrections
- First published.
See an error? Tell us. We correct promptly and say what changed. Our corrections policy.
Disclosure
This is an independent explainer. CERAMICO is not affiliated with, sponsored by, or speaking for any company, brand, agency or person named in this story, and nothing here is official.
Claims are attributed. Where a figure or description comes from a company or an expert, we say so. LEGO® is a trademark of the LEGO Group, which does not sponsor, authorize or endorse this article or film. CERAMICO is not affiliated with the LEGO Group. The animation is an illustrative model, not to scale.
Animations are illustrative. Our films use clay-style 3D models. They are not to scale and are simplified to show how something works.
Trademarks and product names belong to their owners and are used only to identify what we are describing.


